Skip to content
Owner-operated in San Bruno

Heating

Heating Repair in San Bruno

A technician testing a gas furnace control board with a multimeter

When your heating is not keeping the home warm, we check the system, find the fault and explain what the repair involves.

If you ever smell gas, leave the house right away without touching switches, then call PG&E or 911 from outside.

What this involves

We diagnose the problem and explain what a repair involves versus a replacement, so you can decide.

If the equipment is near the end of its life, we explain how a replacement or a heat pump compares.

  • Residential heating repair
  • Clear diagnosis before any work
  • Repair-versus-replace explained
  • Service on the Peninsula

When to reach out

  • No heat. The system runs but the home stays cold.
  • Uneven heat. Some rooms never warm up.
  • A gas smell. Leave the house right away without touching switches, then call PG&E or 911 from outside.

Who Can Repair My Heating System on the Peninsula?

Pacific Sustainable Heating & Air troubleshoots heating systems across the San Francisco Peninsula and can restore your comfort when a crucial component stops working. Is your heat pump blowing cold air, or is your gas furnace rapidly clicking on and off without actually warming the room? Those are clear signs that a crucial component has stopped functioning and requires professional diagnostic attention to prevent further damage.

How Do I Know My Heating System Needs Repair?

Why Is My Heater Blowing Cold Air?

A heater blowing room-temperature or cold air when the thermostat is set to heat means a critical sequence has failed. In a heat pump, this often points to a stuck reversing valve or a compressor issue; in a gas furnace, it might be a failed ignition sequence or a tripped safety limit. Ignoring this symptom forces your blower motor to run continuously, wasting power and driving up your utility bills while your living space stays freezing.

Why Does My Heater Keep Clicking On and Off?

A heater that turns on, runs a few minutes, and shuts down before starting again is short cycling, usually because the equipment is overheating and a safety sensor is forcing a shutdown to prevent a fire or severe mechanical damage. Allowing the system to continuously start and stop can eventually burn out your blower motor, damage your control board, and potentially crack your heat exchanger.

What Do Grinding, Squealing, or Banging Noises From My Heater Mean?

A high-pitched squeal from your heater is often a dying bearing in the blower motor or a failing inducer draft motor, while a loud bang when a gas furnace turns on is often delayed ignition. A failing motor like this needs replacement before it locks up completely. Delayed ignition means gas is building up in the combustion chamber before finally catching a spark and causing a small, dangerous explosion. Your heating equipment should never sound like heavy machinery breaking down inside your walls, attic, or utility closet.

Is a Burning or Exhaust Smell From My Heater Dangerous?

A smell of burning wires or melting plastic from your heater indicates a severe internal failure, while a faint dusty smell the very first time you turn on your heater for the season is normal. A persistent exhaust odor that does not fade suggests a venting issue where dangerous combustion gases are not safely leaving your home, and running the system in this state is a severe safety hazard for your family. If you smell gas, leave the house right away without touching switches, then call PG&E or 911 from outside.

Why Is My Heater Not Responding to the Thermostat?

A heater that does nothing when you bump the temperature up has lost communication between the thermostat and the main control board. The failure could stem from a severed low-voltage wire, a blown fuse on the furnace control board, or a dead thermostat unit on your wall. Tracing the low-voltage circuit with a multimeter shows exactly where the signal is dropping out so the system can fire up again.

What Causes Most Heating Failures?

How Does a Dirty Flame Sensor Stop My Furnace?

A dirty flame sensor cannot detect that the gas furnace burners have successfully lit, so the furnace shuts off the gas valve as a safety precaution. Aging gas furnaces can suffer from heavy carbon buildup on the flame sensor over time, coating this small metal rod in dust and carbon. The fix is cleaning or replacing the sensor and testing its microamp signal to confirm it communicates properly with the main control board.

Why Does My Furnace Blower Stop Working?

A furnace blower often stops because the run capacitor has lost its charge and can no longer provide the boost needed to start the fan blade spinning, even when the motor itself is mechanically fine. The blower motor is the workhorse pushing the conditioned air through your ductwork, but moisture can degrade its components over the years. Testing the capacitor shows whether a simple part replacement will bring your airflow back to life.

Why Is My Heat Pump Not Warming My Home?

A heat pump that is failing to warm your home frequently has a slow refrigerant leak or a malfunctioning defrost control board. Heat pumps must occasionally run a defrost cycle to melt accumulated frost off the outdoor coil, and if the sensors fail, the unit turns into a block of ice that cannot absorb heat from the outside air. Correcting this requires checking the refrigerant charge, testing the defrost thermistors, and making sure the reversing valve shifts as designed.

How Can a Clogged Filter Shut Down My Heating?

A severely clogged air filter chokes off the air your heating system needs to breathe, so internal temperatures spike and trip the high-limit switch, shutting down the burners or heating coils to prevent a complete system meltdown. Airflow restrictions like this are a common cause of heating failures. The fix is clearing the restriction, resetting the safety mechanisms, and testing the temperature rise to check that the system has not suffered permanent heat damage.

Is a Cracked Heat Exchanger Dangerous?

A cracked heat exchanger is a critical failure because it allows carbon monoxide to mix with the air being blown directly into your living spaces. Years of expanding and contracting during intense heating cycles can cause the metal heat exchanger inside an older gas furnace to develop dangerous hairline cracks. When a heat exchanger is compromised, the safe option is to shut the unit down for good and discuss replacement options to protect your household.

What Happens During a Heating Diagnostic Visit?

A heating diagnostic visit starts with the exact symptoms you have experienced, then checks thermostat signals, the power draw on your motors, airflow, and the safety circuits to isolate the exact point of failure. When you call Pacific Sustainable Heating & Air about a heating problem, you work directly with the owner, who has more than 23 years as a union service technician.

Once the mechanical or wiring failure is found, we can explain what broke, why it happened, and what it takes to fix it.

If you have an aging gas system that needs a major repair, it helps to weigh what that repair involves against when a replacement makes more sense.

Heating Repair & Service Coverage Across the San Francisco Peninsula

We provide heating repair for residential heating systems across the San Francisco Peninsula, including the following communities.

San Francisco Peninsula: San Bruno, San Francisco, San Mateo, Burlingame, Redwood City, Palo Alto

Related Services

When an aging heater is facing an extensive repair bill, heat pump installation is one way to move to a modern, efficient system. A severe breakdown is sometimes a clear sign that an aging system is finally at the end of its lifespan and requires a full upgrade rather than another patch. For homes lacking ductwork or struggling with specific cold rooms, a targeted ductless mini split system can provide quiet heating where you need it most.

How Do I Get My Heating System Back on Track?

To get your heating system back on track, have us diagnose the mechanical problem and explain what we find. Living with a broken heater is frustrating, especially when you are not sure what is wrong with it. You do not have to settle for a freezing house or a heating system you cannot rely on during the colder months on the Peninsula.

Contact Pacific Sustainable Heating & Air to request an estimate or schedule your service.

Questions

01 My heat is not working. What should I check first?

If you smell gas, leave the house right away without touching switches, then call PG&E or 911 from outside. Otherwise, check that the thermostat is set to heat and that the breaker has not tripped, and change the filter if it is dirty.

Owner-operated in San Bruno

Ready to talk about Heating Repair?

Call Pacific Sustainable Heating & Air, or send a request and we will get back to you.